Adafruit Feather M0 Basic proto
Adafruit Feather M0 Basic proto
Adafruit Feather M0 Basic proto
Adafruit Feather M0 Basic proto
Adafruit Feather M0 Basic proto
Adafruit Feather M0 Basic proto
Adafruit Feather M0 Basic proto
Adafruit Feather M0 Basic proto
Adafruit Feather M0 Basic proto
Adafruit Feather M0 Basic proto
Adafruit Feather M0 Basic proto
Adafruit Feather M0 Basic proto
Adafruit Feather M0 Basic proto
Adafruit Feather M0 Basic proto
Adafruit Feather M0 Basic proto
Adafruit Feather M0 Basic proto
Adafruit Feather M0 Basic proto
Adafruit Feather M0 Basic proto

Adafruit Feather M0 Basic proto

24,00 €
TTC
3 Produits

  Paiement sécurisé

Connexion SSL et possibilité de régler par Paypal

  Livraison rapide

Livraison offerte dès 100€ d'achat

  Support premium

Une question? On vous répond par mail et téléphone

Adafruit Feather M0 Basic proto

Le module Feather est la nouvelle plateforme de développement d'Adafruit. Elle est légère et fine. Adafruit a designé cette carte avec les nouveaux micro contrôleurs orientés mobilité.

Celui-ci est le Adafruit Feather M0 Basic proto, il possède un espace de prototypage sur la partie droite.

Au coeur du Feather HUZZAH on retrouve un micro-contrôleur ATSAMD21G18 ARM Cortex M0, cadencé à 48MHz et fonctionnant avec une logique sous 3,3V, le même que le nouveau Arduino Zero. Ce chip comprend 256K de Flash (8 fois plus que l'ATMEGA328 ou le 32U4) et 32k de RAM (16x plus)! Ce chip arrive avec un USB natif et peut également être programmé et debuggé en USB sans ajout d'un FTDI !

Pour le rendre plus simple à utiliser sur vos projets portables, Adafruit a ajouté un connecteur compatible toutes batteries Lithium Polymer 3,7V et un système de gestion de charge. Si vous n'avez pas besoin de batterie, la carte fonctionnera par port USB. Mais, si vous en avez besoin, vous pouvez utiliser la carte sur batterie et la brancher en USB pour recharger la batterie. Le Feather va automatiquement basculer sur l'USB si celui-ci est disponible.

Caractéristiques

  • Mesure 2.0" x 0.9" x 0.28" (51mm x 23mm x 8mm) sans les headers soudés
  • Très légère 4,6 grammes
  • ATSAMD21G18 @48MHz avec une alimentation 3,3V
  • 256kB de Flash + 32Kb de RAM
  • Pas d' EEPROM
  • 32,768KHz de quartz pour le cadencement et la RTC
  • 3,3V régulateur avec 500mA de courant de sortie en pic
  • USB Natif avec le bootloader préchargé
  • 20 pins GPIO (Peuvent également être utilisé comme I2C ou SPI)
  • 6 pin analogique d'entrée (12bit)
  • 1 pin analogique de sortie (10bit)
  • Chargeur de batterie Lipo 100mA avec indicateur de charge
  • LED rouge en Pin 13 pour un usage de debug
  • Pin pour la coupure d'alimentation (Power enable)
  • 4 perçages de support
  • Bouton reset

Tutoriels / Liens

Adafruit:2772
3 Produits

Vous aimerez aussi